5 Things To Do To Check In A Furnace Rental Unit

If you think that buying a furnace is tough then you must wait for the cleaning and maintenance part of it. Owning a furnace comes with its own set of hassles and operational faults. Poor heating, inadequate blow, too much noise, abrupt shutdown and vibrations can pose a lot of difficulty in the operation of the furnaces.

Furnace Mississauga

To make things easy, here are 5 steps to acquire optimum performance from the furnace rental units before and during operations.

1. Test fire the igniter:

Igniter in a gas furnace is the most important component. If the furnace does not start despite hitting the ignition button or takes too much time to fire up, the problem lies with the igniter. The furnace sale igniters are often corroded or too tight to strike the contact surface.

Before buying a furnace or finding the issue elsewhere, test fire the igniter first. You can measure the resistance of the igniter surface. Depending on the type of furnace Mississauga igniter switch, the resistance parameters may vary. It could be anywhere between 11 Ohms and 100 Ohms.

Test firing should be done when the igniter is clean, dry and properly set-up.

2. All OK with the flame sensors?

These days, most furnace rental service providers offer units with flame sensors. The flame sensor is a thin metallic rod or wire that is located in front of the gas flame assembly inside the furnace. It is a flame detection unit that prevents the buildup of unburned gas inside the furnace. If there is no flame in the furnace, the flame sensor shuts off the fuel supply automatically.

Flame sensors are susceptible to carbon deposition and moisture attack. If the flame does not arrive, the flame sensor is probably broken. It requires immediate replacement.

3. Cracked heat exchanger or holes

Trust your eyes to get this part done. Though it requires fair knowledge of the heat exchanger, it is easy to manage. Visible heat exchanger kits and dry penetration inspection systems are available in the market for furnace rental owners at affordable prices. However, it is best to avail the services of a HVAC contractor in Toronto to avoid any physical damage to the furnace rental unit.

4. Recheck the installation module

If the furnace rental unit is installed with a flaw, it will cause vibration and lot of noise. The noise levels should not exceed 35 decibels measured from a distance of 1.5 meters from the furnace installation module.

If the installation is faulty, the cracks in the lines and the heat exchanger can cause smoke inside the room. The exhaust gases will be sucked back into the combustion chamber leading to total failure of the furnace rental.

furnace rental mississauga

Faulty installation requires professional intervention. HVAC contractors offer extensive installation and replacement services related to furnace units.

5. Gas leaks

Perform a simple soap bubble test to detect gas leaks. There are electronic gas leak detectors but they are not 100% accurate. Get the gas leak tested by certified gas furnace agency before opting to restart the unit again.


Boiler Installation Tips to Get the Best from Your Rental HVAC Systems

After choosing your boiler units for heating purposes, the next important thing to opt for is a professional expertise in boiler installation. HVAC contractors Toronto offer extensive installation and restoration services for multiple models depending on their age, manufacturer and even the duct lines. In order to get the best out of your boilers and furnace rentals, follow these tips during installation.

furnace rental

Calculate the correct load value

Rental furnace and boilers can deliver a variable output depending on your daily requirements. If you have more members in the family and share a rather larger space, your boiler installation must be done after elaborate load calculation and correction.

Best HVAC contractors in Toronto offer comprehensive software-enabled load calculation services for accurate delivery measurement, across different seasons, water input and temperature variance throughout day and night.

Always pick a simple platform

Based on the size of the boiler, the installation platform can be laid accordingly using the manual guidebook. A 2×8-inch stud lumber and 0.5 inch thick wooden platform with isolation strips are adequate materials to get the best performance out of the unit after boiler installation is complete.

Fan coil unit placement matters a lot

Choose secluded areas to place your fan unit coil. If it is a high-efficiency gas furnace or a boiler unit, the fan coil units can be smartly stacked in areas like attic, garage or small crawl space over the ceiling. As long as the ductwork remains protected from the moisture and dirt, your boiler installation will deliver the best performance for months to come.

Connect the drain tap for overhead systems

A secondary drain tap is recommended for overhead systems as the boiler installation experts avoid connecting the condensate lines to the closed drain systems. The drain line pitch is maintained at quarter of an inch per foot.

If it’s a rental unit, install a secondary drain pan

Consider installing a secondary drain pan and a float switch along with a return air filter box and duct as per the local codes. The HVAC contractors Toronto rental services provided ample space management tips on use of pre-configured suspension platform for overhead boilers and tankless water heater rental units.

Places to avoid

The return air opening requires to be cut so that the fan coil can pass through the opening for highest performance. The places to avoid for return air opening cuts are dining room, kitchen, bathroom and living room. In fact, you should only get boiler installation done where there is a provision to accommodate 180 degree bends.

During the boiler installation process, the expert professionals check for proper fit for the return air box so that it does not interfere with the placement of other materials in the layout.

furnace rental toronto

The bottom line

While installing the water and air distribution components from the tankless water boiler rental unit, the electrical connections too play an equally important role in ensuring best performance out of the thermostat regulation and automated ambient water temperature management.